Earmuffs and ear plugs sold for work in New Zealand are rated with a class from 1 to 5 and an SLC80 number. They tell you how much noise the protector takes off. Choosing the right class isn't about buying the highest number. It's about matching the protector to the noise your team actually works in.
The short answer
Hearing protectors are tested and graded under AS/NZS 1270. The SLC80 rating is the number of decibels the protector cuts for at least 80% of wearers, when it's worn properly. The class groups those ratings into five bands, and each band suits a range of workplace noise:
| Class | SLC80 (dB) | Suits 8-hour noise levels of |
|---|---|---|
| 1 | 10 to 13 | Under 90 dB(A) |
| 2 | 14 to 17 | 90 to 95 dB(A) |
| 3 | 18 to 21 | 95 to 100 dB(A) |
| 4 | 22 to 25 | 100 to 105 dB(A) |
| 5 | 26 or more | 105 to 110 dB(A) |
Above 110 dB(A), get a noise specialist in. You'll often need ear plugs and earmuffs worn together.
How much noise is too much?
In New Zealand, the workplace exposure limit is an average of 85 dB(A) over an 8-hour day, or a peak of 140 dB. Those limits apply whether or not people are wearing hearing protection, and WorkSafe expects businesses to reduce the noise itself before relying on earmuffs and plugs. Protection is the last line of defence, not the first.
Decibels work on a log scale, so every 3 dB increase doubles the sound energy and halves the time you can safely spend in it:
| Noise level | Time to reach the daily limit |
|---|---|
| 85 dB(A) | 8 hours |
| 88 dB(A) | 4 hours |
| 91 dB(A) | 2 hours |
| 94 dB(A) | 1 hour |
| 97 dB(A) | 30 minutes |
| 100 dB(A) | 15 minutes |
Chainsaws, angle grinders, concrete saws and jackhammers commonly run above 100 dB(A), so a few minutes of unprotected use can use up a whole day's allowance. The only way to know your own levels is to measure them with a sound level meter or a noise assessment.
Class 4 vs Class 5: is higher always better?
No. WorkSafe's advice is that protection should be adequate but not excessive: enough to bring the noise at your ear under 85 dB(A) without cutting people off from the sounds they need to hear. Put a Class 5 earmuff on someone in a 92 dB(A) workshop and they'll struggle to hear forklifts, reversing alarms and each other. People who feel cut off tend to lift a cup or pull a plug out, and then the rating means nothing.
So start with the noise level, read off the class from the table above, and only go higher if your workers move between quiet and very loud areas through the day.
Earmuffs or ear plugs?
Both work well when they fit. The choice mostly comes down to the job.
Earmuffs are quick to put on and take off, which suits noise that comes and goes. They're easy to check from across a site, and one size fits most people. They can get hot in summer, and the arms of safety glasses break the seal and let noise in.
Ear plugs are cooler and lighter, they sit comfortably under hard hats, hoods and respirators, and they don't fight with glasses. They need fitting properly every time. A foam plug that isn't rolled down and pushed well into the ear canal gives far less than its rating.
For food processing, choose corded or metal detectable plugs so a dropped plug can't end up in product. For teams going through a lot of plugs, a wall ear plug dispenser holds up to 500 uncorded plugs and keeps them clean.
Headband, helmet or Bluetooth?
If your team wears hard hats, cap-mounted earmuffs clip onto the helmet and swing out of the way when they're not needed. The Hellberg S2C and Armour Hard Hat Earmuff are both Class 5. Check the attachment suits your helmet before you order.
Headband earmuffs, such as the Hellberg S1H (Class 4) and S2H (Class 5), suit everyone else. The Hellberg Secure range is also tuned to the type of noise: Secure 2 is Hellberg's pick for high-frequency noise, and the Secure 3 for very loud noise dominated by low frequencies, such as engines and heavy machinery.
Bluetooth earmuffs, like the Hellberg Xstream LD, let people take calls and stream audio without taking their protection off. That's often the difference between a protector that's worn all shift and one that isn't.
Getting the rated protection in practice
An SLC80 rating comes from lab testing with a good fit. On the job, a few things eat into it:
- Hair, beanies, glasses and hood edges under earmuff cushions
- Foam plugs that aren't fully inserted, or reused until they lose their shape
- Earmuff cushions that have hardened or cracked. Replace them, or the muffs, when they do.
- Taking protection off for "just a minute" in loud areas. Because of the 3 dB rule, short gaps cost a lot.
Quick answers
What is Class 5 hearing protection?
The highest class under AS/NZS 1270, with an SLC80 of 26 dB or more. It suits 8-hour noise levels from 105 to 110 dB(A). Our Armour Bell Ear Plug is Class 5 with an SLC80 of 27 dB.
What is Class 4 hearing protection?
An SLC80 of 22 to 25 dB, for noise levels from 100 to 105 dB(A). The reusable Armour Flanged Ear Plug is Class 4 with an SLC80 of 22 dB.
Is SLC80 the same as NRR?
No. NRR is the American rating and uses a different test method, so the numbers aren't directly comparable. For work in New Zealand, choose by AS/NZS 1270 class and SLC80.
Who pays for hearing protection?
The business. It has to provide the PPE workers need for the job, and it can't charge them for it.
Ready to choose? Browse our full range of hearing protection, from Class 5 ear plugs to Hellberg and Bluetooth earmuffs.