EN 388 Glove Ratings Explained: What the Numbers and Cut Levels Mean

Most work gloves carry an EN 388 code, a short run of numbers and letters like 4544C, printed on the glove next to a small shield symbol. It tells you how the glove scored on abrasion, cut, tear, puncture and, sometimes, impact. Once you can read it, you can compare any two gloves in a few seconds, whatever the brand or price.

The short answer

An EN 388:2016 code reads left to right like this:

  1. Abrasion, scored 1 to 4
  2. Cut (coupe test), scored 1 to 5
  3. Tear, scored 1 to 4
  4. Puncture, scored 1 to 4
  5. Cut (ISO 13997 test), scored A to F
  6. Impact, shown as a P if the glove passed

Higher is better in every position. A 0 means the glove was tested and didn't reach level 1. An X means the test wasn't done or doesn't apply to that glove. Older gloves made to the 2003 version have only the first four numbers.

What each test measures

Test What it measures Level 1 Level 2 Level 3 Level 4 Level 5
Abrasion Rubs against sandpaper until a hole wears through (cycles) 100 500 2,000 8,000 n/a
Coupe cut A rotating circular blade, scored as a cut index 1.2 2.5 5.0 10.0 20.0
Tear Force to tear the material (newtons) 10 25 50 75 n/a
Puncture Force to push a steel point through (newtons) 20 60 100 150 n/a

The ISO 13997 cut test, the letter, works differently. A straight blade is drawn across the material under increasing load until it cuts through, and the result is the force needed in newtons:

ISO cut level A B C D E F
Minimum force (newtons) 2 5 10 15 22 30

Why the letter matters more than the number

The coupe test runs a round blade back and forth until it cuts through. That works on leather and cotton. The fibres in modern cut-resistant liners, such as HPPE, glass fibre and steel yarn, blunt the blade as it goes, which inflates the score. So a glove can earn a coupe 5 without being anywhere near the top of the range.

Under the 2016 revision, a glove whose fibres blunt the coupe blade must also go through the ISO 13997 test, and the letter becomes the result that counts. When that happens the coupe position often shows an X. For any glove sold on its cut resistance, read the letter first.

You can see this in our own range. The Blade Cut 5 Flat Nitrile Glove is rated 4544C. The Blade Core Steel Cut 5/F Food Glove is rated 3X4XF. Both are sold as "Cut 5", but the ISO results put them at 10 newtons and 30 newtons. That's a big difference if you're handling blades.

Reading real codes

Here's how five gloves we stock break down.

  • MaxiFlex Ultimate, 4131: top abrasion, low cut, good tear, low puncture, no ISO letter. A brilliant handling glove, but not a cut glove.
  • Armour Leather Work Glove, 4233: cowhide leather with top abrasion, a low coupe cut score and good tear and puncture results. No ISO letter, so it isn't sold as a cut glove. Leather earns its place on abrasion and toughness, not blade protection.
  • Blade Cut 5 Flat Nitrile, 4544C: tough all round, with a moderate ISO cut of C.
  • Blade Cut 5 Food Glove, 354XD: abrasion 3, coupe 5, tear 4, puncture not tested, ISO cut D.
  • Duty Utility Enforcer, 3241P: the P means the back of the hand passed the impact test, which helps around knocks and pinch points.

Which cut level do you need?

Your risk assessment makes the final call, but this is a fair starting point:

ISO level Typical work
A to B General handling, packing, assembly where edges aren't sharp
C Building and construction, light sheet metal, handling cartons and strapping
D Sheet metal and metal fabrication, glazing, automotive parts
E to F Sharp offcuts and burrs, glass manufacture, blades, food processing and recycling

Two cautions. First, no glove makes you knife-proof. For boning and other hand-knife work in meat and seafood processing, wear a stainless chain mesh glove (tested to EN 1082-1) on the hand that isn't holding the knife. Second, a high cut level often costs you some feel. Go as high as the job needs, not higher, or people take their gloves off to do fiddly work.

Puncture isn't needlestick protection

The EN 388 puncture test pushes a rounded steel point through the material. It tells you how a glove handles splinters, wire ends and sharp debris. It doesn't tell you whether a glove stops a hypodermic needle, which is far finer. If you work with needles or sharps, choose gear specifically sold for needlestick protection, such as the Blade Cut 5 & Needlestick sleeve in our arm sleeves range.

Seen "cut level A4" or "level 9"?

That's the American ANSI/ISEA 105 scale, which runs from A1 to A9. It uses a similar straight-blade machine but reports results in grams, so its levels don't line up neatly with the EN letters. A US-rated glove can still be a good glove. Just don't assume an A5 equals an EN E. If a glove carries both ratings, compare like with like.

The other numbers on your glove

EN 388 covers mechanical risks only. Other hazards have their own shields and codes:

  • EN 407 for heat and flame, with six digits covering flammability, contact heat, convective heat, radiant heat, small splashes of molten metal and large splashes. The Duty Utility Enforcer, for example, is rated X2XXXX: level 2 for contact heat, with the other heat tests not done. See heat resistant gloves.
  • EN 511 for cold, scoring convective cold, contact cold and water penetration. The IceKing Navy Freezer Glove is rated 221.
  • EN 374 for chemicals. Type A, B or C shows how many test chemicals the glove resisted and for how long. See chemical resistant gloves.

Quick answers

Is cut level 5 the highest?

On the old coupe scale, yes, 5 is the top. On the ISO scale used since 2016, F is the top level, and many "Cut 5" gloves score C or D. Check the letter.

What does an X mean in an EN 388 code?

The test wasn't carried out or doesn't apply. On cut-resistant gloves you'll often see an X in the coupe position because the ISO test replaced it.

Do EN 388 ratings matter in New Zealand?

Yes. Most work gloves sold here are tested and marked to EN 388, and it's the easiest way to compare gloves from different brands when you're choosing PPE for a team.

Where do I find the rating?

It's printed on the glove, usually on the back of the cuff under a shield symbol. On our site, it's listed in each glove's specifications.

Ready to choose? Browse cut resistant gloves or see all safety gloves, each with its EN 388 code in the specifications.

Back to blog